10 Plumbing jobs you can do yourself

Posted on at 9:03
19 0

10 Plumbing Tips You Should Know

Plumbing requires knowledge and often very specific tools that only professionals usually have, however, there are some tasks, especially those related to cleaning and maintenance, that you can do yourself.

The fastest, most comfortable and easiest thing to do is always to have a professional plumber to solve any problem related to water in your home, especially if you don’t have time or knowledge. But there are some tasks that you can do very easily and that will help you make the plumber’s visits more spaced and less serious.

Clean and unclog the general siphon pot of the bathroom:

If you do this maintenance task in your bathroom with some regularity, you will avoid serious blockages and major problems in the pipes of your home. It is not a difficult task, although it is somewhat unpleasant, but it is worth undertaking.

It is only necessary to locate the lid of the can, unscrew, remove the lid and extract the can to be able to clean it. Avoid throwing the dirt you remove back into the bathroom or it will go back into the pot, it is better to throw it away as garbage in bags or similar. It does not hurt to add a little plunger or bleach in the pot to clean and keep it clean until further review.

See also  Important aspects To Save Your Taxes

Eliminate clogging of the siphon of the sink or kitchen Sink:

It is common for the kitchen sink or the bathroom sink to show symptoms of obstruction, if you do not clean and check the siphon often to prevent a small problem of dirt from becoming a serious obstruction in the pipes.

Locate the siphon under the sink or sink, it is the tube you will find. Place a basin or similar underneath to collect the water that comes out when removing the registration plugs, access the tube and clean with the help of a wire, for example, remove as much dirt as possible and reassemble. Read more blogs here

Change a Faucet:

Replacing one faucet with another does not entail great difficulties, although everything will depend on the model of faucet you have and the one you intend to put new. In principle, if it is the same in systems, form and design, the change will not be complicated.

You’ll need to be able to disassemble the old or broken faucet, and this can be an expensive task: first, turn off the water to the faucets at the lower faucets. Release the hoses to be able to disassemble the faucet and mount the new one in its place, placing each hose in its corresponding water intake and in the faucet, tighten again and fix the new one.

Renew the showerhead:

Placing a new shower head in the bathtub can be a matter of aesthetics, comfort, necessity and the search for efficiency and water savings, and it is almost always a combination of all these causes.

Changing the shower head is very simple, especially if you choose basic models, which of course must fit and be valid for the rest of the faucet installation you have in the bathtub or shower. Many models are only threaded, so replacement is a matter of seconds.

See also  With online Quran Teacher, you can safely learn the Quran.

Install water consumption limiters:

Water flow limiters, economizers, water aerators or aerators must be installed in all taps in the home to reduce water consumption and, with it, the bill for this supply, actively collaborating in the conservation of a natural asset and as scarce as water.

They are as simple to place on the taps as they are cheap and even aesthetic. You only need to pay attention to the type of tap on which you are going to place the device, most of them are screwed on with total comfort.

Replace sink drain:

If you are tired of the sink stopper always bothering you and never appearing when you need it, it is best to change this type of drain for an automatic one. It is easy and very practical.

Depending on the type of sink you have, this drainage renovation can be more or less simple. In principle, it is necessary to free the sink from the wall a little to be able to release the old drain comfortably. The most common is that it is attached with a simple screw that you can remove, remove the mechanism and put the new one in its place.

Insulate or renew the insulation of the sink and/or bathtub:

This maintenance work is simple, but depending on the conditions of the bathroom it can be heavy and take a little more time. It is essential to keep the joints of sinks and bathtubs clean and in good condition.

If it is a question of sanitizing a joint, the first thing is to remove an old and dirty joint with a cutter and clean it; When the area is free of old silicone, dry and install the new silicone bead. Choose quality and suitable products so that you do not have to do this job very often. For more about water leakage Tips

See also  QuickBooks Enterprise Support – Customer Support Service

Put new hoses:

This is probably one of the most complicated jobs on this list of plumbing jobs, especially since you may need specific tools that you may not have, although you can get by with basics, such as a wrench.

The first thing is to cut off the water so as not to have accidents and work comfortably, buy some hoses that are suitable for your system, since there are different widths and lengths, it is important that they are not tight. You must disconnect the flexible tube from the wall and then from the tap, and put the new one in its place, pressing hard so that the installation does not leak.

Install an ecological system to save water in the cistern:

The double button in the cistern of the bathroom in your house is essential to save water, so if you still do not have it or if it has broken, it is best to replace it; It is not a difficult plumbing job if you buy a basic kit suitable for your type of cistern.

It is essential to cut off the passage of water, remove the lid of the cistern and unscrew the button. Then, you have to empty the water container and disconnect the pipe that carries water to the cistern, remove the mechanism and install the new one.

Replace the tank float:

This is a fairly common fault and it is usually very uncomfortable, but with a little help and knowledge, you can try to solve it yourself, changing the mechanism of the cistern and/or the float, or fixing it, which sometimes is just a matter of straightening lightly the rod that holds the float.

pavel

Hello dear friend! My Name Is Pau, i am content writer on Dymo blog

Related Post